originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 1 of 8 confidential information P1TX6B-SX51-02a product specification sheet
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 2 of 8 confidential information 1.0 features ? 5 transmit lanes and 1 return lane over a single mu ltimode fiber ? low power consumption (1w) ? up to 1000m ? mechanical enclosure serves as heat sink while allo wing for fcc part 15 class a compliance ? no manipulating or compressing the data ? small footprint ? high-speed cml inputs this device is extremely sensitive to electrostatic discharge (esd). at a minimum, all handling must be performed in accordan ce with an ansi-compliant esd control program (ansi/esd s20.20-2007) to mitigate possible esd-induced damage. reliability and life of the device will be adversel y affected if these precautions are not met. this device is a class 3r laser device and can caus e damage to eye sight if used improperly. refer to ansi z136 for proper handling and usage of class 3r devices.
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 3 of 8 confidential information 2.0 absolute maximum ratings parameter symbol min typ max units storage temperature 1 tst c supply voltage 2 3 vcc v operating surface temperature 4 ta c operating humidity 5 rh % durability C sc connector 200 cycles durability C plug-down connector 50 cycles input pin voltage 6 v in v 3.0 optical characteristics C high-speed lanes parameter (per lane) symbol min typ max units average optical power, per lane 7 pout -1.5 dbm optical modulation amplitude 0.0 dbm center wavelength C lane 0 778 nm center wavelength C lane 1 800 nm center wavelength C lane 2 825 nm center wavelength C lane 3 850 nm optical rise/fall time 8 p1tx6b-sx51v p1tx6b-sx51d 200 100 ps 1 stresses listed may be applied without causing dama ge. functionality at or above the values listed is not implied. exposure to these values for extended periods may affect reliability. 2 supply voltage must be present before input signal may be applied 3 module must be powered down (off) before installati on/removal. 4 see outline drawing for measurement point. 5 non condensing. do not operate device if wet. 6 supply voltage must be present before input signal may be applied. driving the device in a power off state may result in permanent damage to the input pins. 7 i= 6ma, t=25c. 8 rise and fall times measured from 20 - 80% . teste d with omron reference circuits.
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 4 of 8 confidential information 4.0 electrical specifications C high-speed lanes parameter symbol min typ max units data rate per lane 9 p1tx6b-sx51v p1tx6b-sx51d gb/s total jitter (rms), per lane 10 t j1 10 ps input differential impedance 100 ohm differential input voltage 2,11 mvp-p single-ended input voltage 2 mvp-p common mode input voltage 2 (ac-coupled input) 2.6 v v operating supply voltage vcc-vee 3.30 v operating supply current icc ma input data pattern dc-balanced 5.0 optical characteristics C bi-directional lanes transmit parameter symbol min typ max units average optical power - lane 4 pavg -1.5 dbm optical modulation amplitude 0.0 dbm wavelength - lane 4 911 nm optical rise/fall time 2000 ps receive parameter symbol min typ max units wavelength - lane 5 980 nm data rate mb/s peak optical input power pin dbm peak optical modulation amplitude pin dbm oma sensitivity 12 -15.00 dbm input data pattern dc-balanced 9 measured with input signals conforming to hdmi rev 1.4a 10 based on a jitter-free source 11 differential cml compatible inputs 12 optical modulation amplitude. based on an unstress ed input signal.
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 5 of 8 confidential information 6.0 electrical specifications C bi-directional lane s transmit parameter symbol min typ max units data rate per lane mb/s total jitter (rms) 13 t j1 25 ps input differential impedance 100 ohm differential input voltage C lane 4 2,14 mvp-p input data pattern dc-balanced receive parameter symbol min typ max units low frequency cutoff f cutoff 35 khz differential output voltage 15 v od 835 mvp-p loss of signal assert sensitivity los sen-on -15.5 dbm loss of signal de-assert sensitivity los sen-off -13.5 dbm loss of signal output low 16 v los v loss of signal output high v los v 7.0 fiber transmission distance data rate om4 (4700 mhz*km) om3 (2000 mhz*km) om1 (160 mhz*km) om2 (500 mhz*km) units 1.65 gbps 2000 1000 200 400 m 3.40 gbps 1000 500 100 200 m 8.0 laser safety the p1tx6-sx51-02 meets class-3r requirements. 17 use proper eye protection and handling practices per ansi z136. 13 based on a jitter-free source 14 differential cml compatible inputs 15 differential back-terminated cml outputs 16 this output is asserted low when a loss of signal i s detected on all lanes 17 lane 4 data input with 50% duty cycle
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 6 of 8 confidential information 9.0 environmental standards omron network products designs and manufactures its products to minimize the negative impact on our environment. as such, the P1TX6B-SX51-02 conforms to a variety of environmental and safety standards standard compliant certificate available rohs yes yes reach yes yes fcc part 15 class a yes no
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 7 of 8 confidential information 10.0 pin numbers and descriptions 18 the tx data module contains a 30 pin connector (df1 2-30ds-0.5v(86)). for information on the specifications of the mating con nector (df12(4.0)-30dp- 0.5v(86)), contact hirose. pin # signal name description 1 gnd ground 2 nc no connect reserved for future use 3 + in0 ch 0 + data input positive differential input for 778nm lane 4 los bi ch 5 los loss of signal C bi-directional channel 5 - in0 ch 0 - data input negative differential input for 778nm lane 6 reset reset microcontroller reset 19 7 + in1 ch 1 + data input positive differential input for 800nm lane 8 uart uart_tx reserved for future use 9 - in1 ch 1 - data input negative differential input for 800nm lane 10 uart uart_rx reserved for future use 11 + in2 ch 2 + data input positive differential input for 825nm lane 12 nc no connect reserved for future use 13 - in2 ch 2 - data input negative differential input for 825nm lane 14 nc no connect reserved for future use 15 + in3 ch 3 + data input positive differential input for 850nm lane 16 en bi enable enable 20 C bi-directional laser 17 - in3 ch 3 - data input negative differential input for 850nm lane 18 en hs enable enable 20 C high speed lasers 19 gnd ground 20 nc no connect reserved for future use 21 - in4 ch 4 - data input negative differential input for 911nm lane 22 nc no connect reserved for future use 23 + in4 ch 4 - data input positive differential input for 911nm lane 24 nc no connect reserved for future use 25 + td5 ch 5 - data output positive differential outp ut for 980nm lane 26 nc no connect reserved for future use 27 - td5 ch 5 - data output negative differential outp ut for 980nm lane 28 vcc 2 voltage input +3.3 volt input 29 gnd ground 30 vcc 2 voltage input +3.3 volt input 18 verify pin assignments and polarity before powering on device 19 reset to be pulled high for normal operation 20 enable to be pulled up to vcc for normal operation
originator: c. eng date: 3/9/2012 document no. doc002325 rev a P1TX6B-SX51-02a product specification sheet 8 of 8 confidential information 11.0 dimensions the sx51-02 data module is designed to work with a standard sc ferrule only. insertion of any other type may result in damage. dimensions and orientation are for reference only . customers can request final, detailed dimensions, or a cad drawing, throu gh your omron sales representative. dimensions are in mm temperature measurement point
|
